CIM™ Industrial Membrane

CIMTM Industrial Membrane Systems are cold applied (by spray, squeegee or roller), high-solids liquids that cure to a durable, flexible, U.V. resistant, seamless, impermeable barrier to water and most aqueous agents. This asphalt modified polyurethane material may be applied in a range of thicknesses to permanently bond to any properly prepared surface. CIM Systems are quickly applied and cure rapidly to allow for minimal facility downtime (generally less than one day). CIM Membranes have been successfully applied for over 20 years, are U.L. approved and meet stringent California VOC and NSF 61 (potable water) requirements.

Available in pourable and trowel grade consistency in industrial, potable water grades and roofing grades.

Use on: Secondary and waste containment, steel and concrete water tanks, concrete cracks, roofs, transportation equipment, cooling towers, pond liners, deionized water tanks and wherever liquids need to be kept where they belong.

Resistant to: acids, caustics, bleach, ferric chloride, hydrogen sulfide, food and animal waste and many other chemicals. Suitable for secondary containment of fuel oils.

Two part system. Activator in plastic bottle. Four gallons to a case.

CIM 1000 Gal. Item #506100 CIM Trowl Grade Gal. Item #506110

CIM 1000 5 Gal. Item #506105 CIM Trowl Grade 5 Gal. Item #506115

Amerlock 400

Amerlock 400 is a high (80-85%) solids, two part epoxy paint that is unsurpassed in performance in areas where complete preparation is difficult or impossible. It is an extremely versatile and durable maintenance coating. Amerlock 400 is available in a variety of colors, including aluminum (Amerlock 400AL) and therefore does not require a topcoat. For extended weatherability or special uses a topcoat may be desired. Can be applied on damp surfaces.

Amerlock 400's low solvent level reduces the chances for film pinholing and solvent entrapment at the substrate-coating interface. Amerlock 400 is used in those areas where sand blasting is impractical or impossible. As a maintenance coating, Amerlock 400 protects steel structures in industrial facilities, bridges, tank exteriors, marine weathering, offshore oil tanks, piping, roofs, water towers and other exposures. Amerlock 400 has good chemical resistance to splash/spillage, fumes and immersion in neutral, fresh and saltwater.

Packaged in Gallons. Two 2 gal. kits per case. Item #404140

Also available in 5 gallon pails.

Rust Destroyer

Rust Destroyer is the only patented rust converting paint primer engineered to be applied directly over rusted metal, new bare metal or rusted painted metal. It is guaranteed to stop rust up to five full years when applied in accordance with label directions. Remove loose rust and apply two thin coats ten minutes apart to a dry film thickness of 3 mils per coat. One spray can covers approximately 15 square feet. Rust Destroyer is non-toxic and has been USDA and FDA approved. Heat resistant to 800F

Use on any rusted metal and also to prime metal where paint has been removed by welding or abrasion. This is an exceptional universal metal primer that can be used anywhere there is a need to stop rust from continuing on old steel or forming on bare or newly exposed steel, iron or sheet metal.

Aerosol can contains 13 oz. 12 per case. Item #401282

Gallons packed 4 per case. Item #401284. Also available in 5 gallon pails.

Seal Guard

SealGuard is an all purpose, colored, two component, 100% solid epoxy system that is rolled out as a coating to provide a smooth, glossy and easily cleaned surface which is extremely durable. It resists abrasion, and penetration of moisture, oil, dirt, and a number of chemicals. SealGuard contains no solvents and is almost odorless during application. It is available in ten colors, (red, white, green, gray, light gray, yellow, blue, light blue, tile red and tan.) The high gloss, tile-like finish is stain resistant and unaffected by oil, gasoline, grease, strong detergents, salt and most other substances commonly found in industrial environments.

Used in boiler rooms, mechanical rooms, warehouses, machine shops, kitchens, clean rooms, laundries, hospitals, basements, garages and other areas where a very tough floor is needed.

SealGuard can be installed over almost any sound substrate including, concrete, steel, wood, fiberglass, clay tile, stone and terrazzo. It sets up in 6 to 8 hours and can be re-coated if desired for a thicker coating.

Mixing ratio two parts resin to one part hardener.

Packaged in: 1 1/2 Gallon Kit Item # 504115

4 1/2 Gallon Kit Item # 504110

15 Gallon Kit Item # 504111

Epoxy ConcretePatch Kit

SEALPRO Epoxy Concrete Patch Kit is a 100% solid, two component compound which can be used to restructure, resurface or pitch a floor prior to the application of a top coat. It is an economical alternative to more costly compounds when a high build system is required. Each kit contains resin, hardener and aggregates.

 

Use to rebuild spalled or eroded concrete sub-floors, and to pitch or level prior to applying floor top coats. May be combined with crushed stone to fill deep holes and construct curbs. Also used to fill deep holes, cracks or pits in concrete. This system is always mixed two parts resin to one part hardener by volume. Sets in one to four hours.

 

Packaged in 5 gal kit. Item #504116

Table of Contents

Re-Crete 20

Re-Crete 20 is a 20 minute setting hydraulic cement that is used to fill holes in concrete. This general purpose material contains portland cement, special hardeners and set accelerators to provide initial set time in 15 minutes and a final set time of 35 minutes. Product mixes with water and reaches a compression strength of 3,000 psi in 24 hours which is twice the strength of regular concrete.

Meets industrial, commercial, construction and residential standards. Strength tests and setting times established in accordance with ASTM C-109, ASTM C-226 and ASTM C-109. Compressive strength: 1 day - 3,000psi; 3 days - 5,000 psi; 28 days - 6,500 psi.

Use to repair cracks in all concrete, concrete pipe, precast products, floor cracks, concrete steps, walls, columns, blocks, sidewalks, driveways, vaults and for waterproofing. Re-Crete is ideal for overhead and vertical use because it has a putty-like consistency which allows shaping and molding.

Supplied in 5 gallon plastic buckets. Item #808455

Table of Contents

Water Stop

Water Stop is a light gray cemetitious powder that is mixed with water to form a very fast setting hydraulic plug material that can be used in adverse and extreme environmental conditions. Can be used to stop water from flowing through cracks in concrete and masonry. Its plastic putty like form and its set time of only 45 seconds make Water Stop ideal for stopping water which is pouring through cracks. Pot life is about one minute.

Use to stop pouring water which is coming through concrete and masonry. In dry form Water Stop can be used in conjunction with Deep Penetrating Sealer to rub into hairline cracks even when water is still coming through the cracks. Use with oakum to plug the most stubborn leaks in concrete walls, floors, foundations, sidewalks, driveways, vaults and similar areas.

Supplied in 5 gallon plastic buckets. Item #808950

Deep Penetrating Sealant II

Deep Penetrating Sealer II is a moisture vapor barrier & waterproofing compound for concrete. It is a highly enriched, alkaline neutralizing, silicate based solution that is specifically designed to penetrate deeply into concrete materials and chemically form a protective crystalline barrier beneath the surface of new and existing concrete.

Deep Penetrating Sealer II is ideal for waterproofing and strengthening concrete where water intrusion is evident or possible and it is used extensively on basement walls, tunnels, manholes and other below grade vertical and overhead surfaces. It is also used as a waterproofer under flooring systems and does not affect the adhesion of epoxies or urethanes. It is completely absorbed into the concrete and it does not change the color or texture of the surface. It is nontoxic and may be painted.

Is not affected by ultraviolet light, abrasion and most harsh chemicals, and will permanently seal and waterproof against the harmful effects of water intrusion, freeze-thaw cycle damage, deicing salts and chloride ion migration.

Packaged in: 1 Gallon Bottle. Item #808300

5 Gallon Bucket. Item #808305

55 Gallon drums. Item #808355

Seal Crete

 

Seal Krete Waterproofing Sealer is a water-based, very low VOC, strong-binding, clear acrylic, penetrating sealer/primer. It penetrates deepIy into the pores of concrete, binding to the sand and cement particles, forming a tough, flexible and breathable film. It is formulated for use on interior and exterior concrete, stucco, brick and masonry surfaces.

May be used on wood, stone, porous roof tile, asphalt shingles, adobe, plaster, drywall, coral, limestone, grout, painted aluminum siding, vinyl siding. Seal Krete is a 10% solids, low odor acrylic emulsion that applies milky white, which aids in uniform coverage, and dries in 1 to 2 hours to a tough, flexible, clear sealer. It is nonflammable, nonhazardous and nonstaining.

Helps to reduce efflorescence, erosion, chalking, spalling, cracking, rotting and other effects due to water penetration. Seals and binds chalky surfaces, provides dustproofing on bare horizontal masonry surfaces, (1 thin coat). Can be painted.

Packaged in one Gallon pail, Item #808500 & 5 Gallon Bucket Item #808505

Table of Contents

 

Skid Proof^® EZ-Coat

Skid-Proof® EZ-Coat, brush and roll, is a waterborne, acrylic based, quartz, non-cementious, anti-skid coating. It is environmentally safe, nonflammable, nonhazardous, and contains low (less than 40 grams/liter) VOCs. Skid-Proof EZ-Coat, is neutral in color allowing the availability of various colors by adding your desired color of Exterior Gloss, Semi-Gloss, Satin Acrylic, Acrylic Floor Enamel, or Industrial Acrylic Enamel Paint at a ratio of 1 quart to a 13 pound pail or 1 gallon to a 40 pound pail of Skid-Proof EZ-Coat. Do not use Flat Latex or interior paint. Simply mix thoroughly when adding paint. Skid-Proof EZ-Coat, when fully cured, is hard and tough, yet flexible. On horizontal surfaces it is anti-skid. On vertical surfaces (i.e., risers and stairways), it provides a heavy duty textured coating. When fully cured it is waterproof and resistant to weather, impact, salts, and chlorine.

Skid-Proof EZ-Coat is used as a decorative, protective, anti-skid coating for long term preservation of various surfaces including concrete, wood, plywood, and primed metal, against weather deterioration. See label for complete information. Skid-Proof EZ-Coat can be used indoors and outdoors on horizontal surfaces including high traffic areas, such as walkways, patios, stairs, pool decks, balconies, ramps, driveways, carports, and more.

Packaged in 13# and 50# Pails. Item #808710

Table of Contents

Graffiti Barrier

Graffiti Barrier is a waterborne, biodegradable, scrubable, liquid plastic film coating used to keep paint and other graffiti materials from adhering to walls. It is a specially formulated waterborne polymer dissolved in water to yield a clear biodegradable and cleanable film. This product is environmentally safe and contains no volatile organic compounds (VOC's). Apply Graffiti Barrier with brush, roller or spray equipment. Use two or three coats. This is a sacrificial coating and must be reapplied after the removal of the graffiti by pressure washing with water.

Graffiti Barrier is recommended to be used over concrete, brick, cement, plaster, some metals and some painted surfaces. Metals and painted surfaces must be tested for suitability.

Packaged in:

Five gallon plastic buckets. Item #804505

55 gallon drums. Item #804555 Table of Contents

 

Heavy Duty Anti-Rust

SEALPRO Heavy Duty Anti-Rust is an effective rust preventative under the most severe conditions. It is a cut back type product, that after evaporation of the solvent, leaves a durable film that adheres firmly to metal surfaces, is dry to the touch, does not flake, is self-healing when broken, and resists flow up to 175°F.

USES:

Industry: Protects tools, dies, machines. Excellent for machinery or parts stored out of doors or for protection of parts from corrosion during shipment.

Farm: Protects all equipment subject to humidity, salt, and other corrosive elements. Will protect outside steel structures.

Marine: Protects shafts, boat trailers - all metal surfaces exposed to air, excessive humidity or salt water atmosphere.

 

Packaged in 14 oz aerosol spray cans. 12 Per case. Item #401154

Table of Contents

 

Stainless Steel Mechanical Repair

Stainless Steel Mechanical Repair System is absolutely the smoothest handling, strongest, most impact resistant steel rebuild system available. A truly premium combination of epoxy matrix and high grade stainless steel for precision and long term dimensional stability. The stainless steel system is available as a liquid and a putty:

Both liquid and putty are mixed 1:1, have a viscosity of 6500 cps, a working time of 20 min. and a cure time of 4-8 hrs. It can be used up to 225° F. The liquid has a tensile strength of 4800 psi and an ultimate compressive strength of 18,000 psi. The putty has a tensile strength of 4500 psi and an ultimate compressive strength of 18,000 psi.

This system is used to restore geometry, rebuild wear rings, refit keyways, repair hydraulic cylinders and for tooling.

 

Putty- 2.5lb per kit. 4 per case. Item #502102

Liquid- 2.5lb per kit. 4 per case. Item #502120

Ceramic Mechanical repair

Ceramic alloy composite is a finely divided alumina (as the wear resistant media) and micron range size graphite powder combination that forms a smooth, brushable liquid or a buttery putty. This system has exceptional strength, chemical inertness, and a slick, anti-friction work surface for long life abrasion control.

Both liquid and putty are mixed 1:1, have a working time of 20 min., a cure time of 4-8 hrs. , and can be used up to 225° F. The liquid has a tensile strength of 6500 psi and an ultimate compressive strength of 17,500 psi. The putty has a tensile strength of 5800 psi and an ultimate compressive strength of 17,500 psi.

This system is used to rebuild pump casings and impeller blades, resurface flanges, reline valves and provide a smooth, noncorrosive glaze surface.